AEON LABS Z STICK 2 CONTROLLER HOW TO
AEON LABS Z STICK 2 CONTROLLER SERIAL
AEON LABS Z STICK 2 CONTROLLER DRIVERS
AEON LABS Z STICK 2 CONTROLLER FULL
AEON LABS Z STICK 2 CONTROLLER DOWNLOAD

Pressing the Action Button will not have any effect while in SerialAPI- Mode. While in SerialAPI-mode, Z-Stick is always listening (it is awake and always in RX receive mode) for instructions and acts as a Z-Wave adapter and responds to commands sent through USB by the host processor software.Дў. To initiate SerialAPI-Mode, plug Z-Stick into the USB connector of the host (i.e. SerialAPI-Mode: Allowing a Host Processor To Take Control of the Z-Stick and Take Part in the Z-Wave Network. Short press the Action Button 5 times again, Z-Stick will automatically exit the IMA feature. A red LED light means that the current communication has failed. A purple LED light means that the current communication quality is less than 95% on 0dBm. An orange LED light means that the current communication quality is more than 95% on 0dBm. A green LED light means that the current communication quality is more than 95% on -7dBm.

If the colour of the LED light changes to purple and is then followed by fast blinking t hat means it goes into the IMA feature.В The colour of the LED indicator will be changed according to the network health level. The different colour of LED on Z-Stick indicates the communication quality between the Central Controller and the current location of Z-Stick in the network. When Z-Stick acts an independent / secondary controller that has been un-plugged from the USB host, it also can measure the network health in Z-Wave network. The different colour of LED indicates the communication quality between the Z-Stick Controller and devices in the network.

AEON LABS Z STICK 2 CONTROLLER SERIAL

When Z-Stick is in Serial API- Mode and acts a primary controller, it can measure the network health for each device in the network.

Installation and Maintenance Application (IMA) feature.

AEON LABS Z STICK 2 CONTROLLER HOW TO

You can learn how to use Backup Software here to backup, and restore:

AEON LABS Z STICK 2 CONTROLLER DOWNLOAD

You can download the installation setup for Backup Software here: This way you will never have to re-do your network if there are catastrophic issues. You are able to backup the Z-Stick Gen5 using our Z-Stick Gen5 Backup Software in any case you need to restore an older save of your network, or replace a failed Z-Stick Gen5. You can find all known third party softwares in this link:

AEON LABS Z STICK 2 CONTROLLER FULL

In order to use the Z-Stick Gen5 and control your Z-Wave network, you must download a third party software to have full control over your software. Repeat step 2 for each device you wish to exclude. The orange LED will then return to blink fast, indicating readiness for further device exclusions. (The blue LED on Z-Stick will immediately stay solid for 2 seconds to indicate successful removal from the network.)ДЈ. To remove a Z-Wave device from the network, simply go to the device with Z-Stick and press the button on the device you wish to remove. Then press and hold down the Action Button for approximately 2 seconds. To initiate Removal-Mode, unplug Z-Stick from the USB connector. Removal-Mode: Deleting/ Removing/Excluding Z-Wave Devices from the Z-Wave Network.ДЎ.

Tap Z-StickвЂ™s Action Button to turn it off or it will automatically exit the removal mode after 30 seconds of inactivity. Repeat step 2 for each device you wish to include.Д¤. The blue LED will then return to blinking slowly, indicating readiness for further device inclusions. (The blue LED on Z-Stick will blink fast during a network neighbour discovery and stay solid for 2 seconds to indicate successful inclusion of the device into the network.)ДЈ. To include a new Z-Wave device into the network, simply go to the device with Z-Stick and press the button on the device you wish to include. To initiate Inclusion-Mode, unplug Z-Stick from the USB connector and then tap the Action Button. Inclusion-Mode: Adding/Including Z-Wave Devices into the Z-Wave Network.ДЎ. We recommend free software Domoticz if you are just getting started, you can view this guide here: Z-Stick Gen5 and how to get started with Domoticz. To quickly get started, please follow our Z-Stick Gen5 Quick Start - Just the essentials article.

AEON LABS Z STICK 2 CONTROLLER DRIVERS

Software drivers for the вЂњZW050x_USB_VCP_ PC_DriverвЂќ may need to be installed in order for Z-Stick to be recognized on some computers. Both Inclusion-Mode and Removal-Mode require Z-Stick to be unplugged from the USB connector of the host, while SerialAPI-Mode requires that Z-Stick to be plugged into the USB connector of the host.

Z-Stick operates in three distinct modes: Inclusion-Mode, Removal- Mode and SerialAPI-Mode.

Aeon labs z-stick 2 controller